Home |
Search |
Today's Posts |
|
#1
|
|||
|
|||
On Fri, 04 Mar 2005 01:13:39 GMT, "Thomas Magma"
wrote: Wow this is a long thread. Don't really know where I should put my two bits in, but here it goes. I have designed several RF PA sections in the past. 500MHz at about 50W. Pretty easy stuff if you have the right tools and know how to use them. The tools I like using for matching the power output FET is two triple stub tuners. One on the input of the FET and one on the output. So it goes...pre-amp (50 ohm output) - stub tuner - FET - stub tuner - 50 ohm dummy pad - spectrum analyzer. Then just tune the stubs for the performance you desire, these include: efficiency (thermal issues), harmonic content, spurious emissions, load VSWR considerations, cold start, ect. Then remove the FET and look into the triple stub tuners with the network analyzer. Model and duplicate the network out of discrete components that can handle the voltage/power, send the design off to the enviro test lab, and head home early for the day. Cheers, Thomas Hi Thomas, Thanx, your two bits were worth more than the academic plug nickel. This is something that our original poster should hearken to as his needs were obviously production oriented. Bench experience will trump cut-and-paste theory in a heart-beat. However, triple stub is pretty aggressive. How long did it take you to flatten response? 73's Richard Clark, KB7QHC |
#2
|
|||
|
|||
Response is flattened through gain controlling the pre-amp from a look-up
table held in the micro's EEPROM. The alignment procedure is automated using the HB-IP bus from the spectrum analyzer and a computer. The computer/analyzer also looks for harmonic content and spurious emissions during this procedure. Think it takes about ten seconds to do this. "Richard Clark" wrote in message ... On Fri, 04 Mar 2005 01:13:39 GMT, "Thomas Magma" wrote: Wow this is a long thread. Don't really know where I should put my two bits in, but here it goes. I have designed several RF PA sections in the past. 500MHz at about 50W. Pretty easy stuff if you have the right tools and know how to use them. The tools I like using for matching the power output FET is two triple stub tuners. One on the input of the FET and one on the output. So it goes...pre-amp (50 ohm output) - stub tuner - FET - stub tuner - 50 ohm dummy pad - spectrum analyzer. Then just tune the stubs for the performance you desire, these include: efficiency (thermal issues), harmonic content, spurious emissions, load VSWR considerations, cold start, ect. Then remove the FET and look into the triple stub tuners with the network analyzer. Model and duplicate the network out of discrete components that can handle the voltage/power, send the design off to the enviro test lab, and head home early for the day. Cheers, Thomas Hi Thomas, Thanx, your two bits were worth more than the academic plug nickel. This is something that our original poster should hearken to as his needs were obviously production oriented. Bench experience will trump cut-and-paste theory in a heart-beat. However, triple stub is pretty aggressive. How long did it take you to flatten response? 73's Richard Clark, KB7QHC |
#3
|
|||
|
|||
On Fri, 04 Mar 2005 16:47:05 GMT, "Thomas Magma"
wrote: Response is flattened through gain controlling the pre-amp from a look-up table held in the micro's EEPROM. The alignment procedure is automated using the HB-IP bus from the spectrum analyzer and a computer. The computer/analyzer also looks for harmonic content and spurious emissions during this procedure. Think it takes about ten seconds to do this. Hi Thomas, 10 seconds to adjust all 6 stubs? 73's Richard Clark, KB7QHC |
#4
|
|||
|
|||
No the triple stub tuners are only for development. Production boards have
discrete components to form the match network. Power levelling or "flattening the response" is computer adjusting the output power to compensate for the reactive components to ensure a constant output power over the entire band of the radio. We also put in a small temperature compensation coefficient into the EEPROM because the PA tends to put out more power when it is cold. "Richard Clark" wrote in message ... On Fri, 04 Mar 2005 16:47:05 GMT, "Thomas Magma" wrote: Response is flattened through gain controlling the pre-amp from a look-up table held in the micro's EEPROM. The alignment procedure is automated using the HB-IP bus from the spectrum analyzer and a computer. The computer/analyzer also looks for harmonic content and spurious emissions during this procedure. Think it takes about ten seconds to do this. Hi Thomas, 10 seconds to adjust all 6 stubs? 73's Richard Clark, KB7QHC |
#5
|
|||
|
|||
On Fri, 04 Mar 2005 17:39:04 GMT, "Thomas Magma"
wrote: No the triple stub tuners are only for development. Hi Thomas, I thought 10 seconds was awful quick. How long would it take to flatten the response when manually adjusting the triple stub tuners? What merit did you find with triple that could not be found with double stub tuners? 73's Richard Clark, KB7QHC |
#6
|
|||
|
|||
If your amp has to operate over a wide frequency range it is not likely that
you can flatten the response just with stubs. Stubs should be looked at as more single frequency devices than broadband networks. But you can use the stubs to plot out the appropriate impedance curve on the Smith Chart to ensure a flat response when you model in the discretes. I usually just try to get the flatness of the response as close as possible and rely on a software calibration routine to flatten it off. Saves a lot of time. It's my understanding that a triple stub tuner of the right length can reach anywhere on the Smith Chart where as a double stub can not. "Richard Clark" wrote in message ... On Fri, 04 Mar 2005 17:39:04 GMT, "Thomas Magma" wrote: No the triple stub tuners are only for development. Hi Thomas, I thought 10 seconds was awful quick. How long would it take to flatten the response when manually adjusting the triple stub tuners? What merit did you find with triple that could not be found with double stub tuners? 73's Richard Clark, KB7QHC |
#7
|
|||
|
|||
On Fri, 04 Mar 2005 19:09:20 GMT, "Thomas Magma"
wrote: If your amp has to operate over a wide frequency range it is not likely that you can flatten the response just with stubs. Hi Thomas, Certainly not as conventional Triple Stubs. However, care to provide some of the cogent details of that particular project? Any interesting insights? 73's Richard Clark, KB7QHC |
#8
|
|||
|
|||
Thomas Magma wrote: No the triple stub tuners are only for development. Production boards have discrete components to form the match network. Power levelling or "flattening the response" is computer adjusting the output power to compensate for the reactive components to ensure a constant output power over the entire band of the radio. We also put in a small temperature compensation coefficient into the EEPROM because the PA tends to put out more power when it is cold. Richard was asking how long it took you to tune the triple stub filters during devolpment. I am curious about the exact nature of the impedance transmformation these devices provided. jk "Richard Clark" wrote in message ... On Fri, 04 Mar 2005 16:47:05 GMT, "Thomas Magma" wrote: Response is flattened through gain controlling the pre-amp from a look-up table held in the micro's EEPROM. The alignment procedure is automated using the HB-IP bus from the spectrum analyzer and a computer. The computer/analyzer also looks for harmonic content and spurious emissions during this procedure. Think it takes about ten seconds to do this. Hi Thomas, 10 seconds to adjust all 6 stubs? 73's Richard Clark, KB7QHC |
#9
|
|||
|
|||
Richard Clark wrote:
On Fri, 04 Mar 2005 01:13:39 GMT, "Thomas Magma" wrote: Wow this is a long thread. Don't really know where I should put my two bits in, but here it goes. I have designed several RF PA sections in the past. 500MHz at about 50W. Pretty easy stuff if you have the right tools and know how to use them. The tools I like using for matching the power output FET is two triple stub tuners. One on the input of the FET and one on the output. So it goes...pre-amp (50 ohm output) - stub tuner - FET - stub tuner - 50 ohm dummy pad - spectrum analyzer. Then just tune the stubs for the performance you desire, these include: efficiency (thermal issues), harmonic content, spurious emissions, load VSWR considerations, cold start, ect. Then remove the FET and look into the triple stub tuners with the network analyzer. Model and duplicate the network out of discrete components that can handle the voltage/power, send the design off to the enviro test lab, and head home early for the day. Cheers, Thomas Hi Thomas, Thanx, your two bits were worth more than the academic plug nickel. This is something that our original poster should hearken to as his needs were obviously production oriented. I doubt you understand what he wrote. I can't fathom why you would be concerned with the OP when your own difficulties are so acute. Bench experience will trump cut-and-paste theory in a heart-beat. How would you know? However, triple stub is pretty aggressive. How long did it take you to flatten response? How long will it take you to figure out that he wrote not a wisp of a word on what the "output-Z" of the amplifier is? He did write that he determines how the amp was loaded to acheive power, something I've been saying is the prime concern. |
#10
|
|||
|
|||
Hi gwhite,
I would have to agree with you on most everything you have said through this thread. I once saw my boss (with his "PHD") try to model and match a power amp based on the small signal parameters off the datasheet. He insisted that the stated input and output impedances were characteristic parasitics of that amp and wouldn't change between a small or large signal. It was kind of pathetic to watch him struggle for over a month on the matching network, and I think he had resorted to guessing in the end. I've often questioned why manufactures put small signal parameters on their datasheets? Makes no sense to me. Even if they do publish some large signal parameters it is unlikely to be the exact same mode of operation that you need for your project. Playing with triple stub tuners on PA's has shown me that there are many combinations of input and output impedances that appear to give similar results at any one frequency, but give different results at others frequencies. So it's a matter of finding the input and output impedance that give you adequate performance over the entire scope of your project. Thomas "gwhite" wrote in message ... Richard Clark wrote: On Fri, 04 Mar 2005 01:13:39 GMT, "Thomas Magma" wrote: Wow this is a long thread. Don't really know where I should put my two bits in, but here it goes. I have designed several RF PA sections in the past. 500MHz at about 50W. Pretty easy stuff if you have the right tools and know how to use them. The tools I like using for matching the power output FET is two triple stub tuners. One on the input of the FET and one on the output. So it goes...pre-amp (50 ohm output) - stub tuner - FET - stub tuner - 50 ohm dummy pad - spectrum analyzer. Then just tune the stubs for the performance you desire, these include: efficiency (thermal issues), harmonic content, spurious emissions, load VSWR considerations, cold start, ect. Then remove the FET and look into the triple stub tuners with the network analyzer. Model and duplicate the network out of discrete components that can handle the voltage/power, send the design off to the enviro test lab, and head home early for the day. Cheers, Thomas Hi Thomas, Thanx, your two bits were worth more than the academic plug nickel. This is something that our original poster should hearken to as his needs were obviously production oriented. I doubt you understand what he wrote. I can't fathom why you would be concerned with the OP when your own difficulties are so acute. Bench experience will trump cut-and-paste theory in a heart-beat. How would you know? However, triple stub is pretty aggressive. How long did it take you to flatten response? How long will it take you to figure out that he wrote not a wisp of a word on what the "output-Z" of the amplifier is? He did write that he determines how the amp was loaded to acheive power, something I've been saying is the prime concern. |
Reply |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Discone antenna plans | Antenna | |||
The "TRICK" to TV 'type' Coax Cable [Shielded] SWL Loop Antennas {RHF} | Antenna | |||
Poor quality low + High TV channels? How much dB in Preamp? | Shortwave | |||
X-terminator antenna | CB | |||
Outdoor Antenna and lack of intermod | Scanner |