There is a two-component epoxy putty, I have used this to
water-proof/weather-proof different kludges of mine--even to construct
standoff, insulators and unique hardware bits... my latest stash came from
the 99-cent store... "bondo" can also be used from autosupply stores (used
to fill dents in auto bodies) with good success (strength is somewhat
less)...

Warmest regards,
John
--
Marbles can be used in models with excellent results! However, if forced
to keep using all of mine up... I may end up at a disadvantage... I seem
to have misplaced some already!!!


"gb" wrote in message
...
| "ml" wrote in message
| ...
|
| My dipole (center) has the usual wire thru a eye bolt and wrapped around
| itself like the arrl manual typically shows.
| My ladder line transitions to the wire itself and is also wrapped around
| questions:
| Rather than soldering it, (thought it might be stiff and break??) I
used
| proper sized wire clamps(w/teeth) [two of them , torqued proper]
| wonder if a good compression fit is OK ?
| Or will corrosion eventually make this a poor connection?
| It's still new enough i could clean it and solder it
| Any thoughts? I would hate to throw off harmonics
|
| Split bolts are used by electricians.
| If you are concerned about corrosion, wrap the joint with good electrical
| tape (rated for outdoor usage - UV and temperature range) - some power
| companies do this for outdoor connections subject to corrosion, etc.
|
| gb
|
|

John Smith wrote:
There is a two-component epoxy putty, I have used this to
water-proof/weather-proof different kludges of mine--even to construct
standoff, insulators and unique hardware bits... my latest stash came from
the 99-cent store... "bondo" can also be used from autosupply stores (used
to fill dents in auto bodies) with good success (strength is somewhat
less)...

Warmest regards,
John
You need to buy a roll of cablers seal , sold under different names but
its essentially butyl rubber tape that pressure seal when rapped , only
a few bucks a roll and lasts a decade ( sticks really well but try to
remove it )

I have used that tape, or a product just like it--but prefer the epoxy...
you can work it like clay--strong as steel and apparently excellent
insulating qualities... wonderful stuff really...

Warmest regards,
John
--
If "God"--expecting an angel... if evolution--expecting an alien... just
wondering if I will be able to tell the difference!

"Atec" wrote in message
...
| John Smith wrote:
| There is a two-component epoxy putty, I have used this to
| water-proof/weather-proof different kludges of mine--even to construct
| standoff, insulators and unique hardware bits... my latest stash came
from
| the 99-cent store... "bondo" can also be used from autosupply stores
(used
| to fill dents in auto bodies) with good success (strength is somewhat
| less)...
|
| Warmest regards,
| John
| You need to buy a roll of cablers seal , sold under different names but
| its essentially butyl rubber tape that pressure seal when rapped , only
| a few bucks a roll and lasts a decade ( sticks really well but try to
| remove it )

John Smith wrote:
I have used that tape, or a product just like it--but prefer the epoxy...
you can work it like clay--strong as steel and apparently excellent
insulating qualities... wonderful stuff really...

Warmest regards,
John
I dislike it ('poxy), but whatever .

I applied the tape, played a Ying Yang Twins CD and nothing happened.

"Atec" wrote in message
...
John
You need to buy a roll of cablers seal , sold under different names but
its essentially butyl rubber tape that pressure seal when rapped , only
a few bucks a roll and lasts a decade ( sticks really well but try to
remove it )

Fred:

I might agree, I got epoxy up the "ying-yang" and a few rock-n'-roll cd's,
so got it covered!!!

Warmest regards,
John
--
If "God"--expecting an angel... if evolution--expecting an alien... just
wondering if I will be able to tell the difference!

"Fred W4JLE" wrote in message
...
|
| I applied the tape, played a Ying Yang Twins CD and nothing happened.
|
| "Atec" wrote in message
| ...
| John
| You need to buy a roll of cablers seal , sold under different names but
| its essentially butyl rubber tape that pressure seal when rapped , only
| a few bucks a roll and lasts a decade ( sticks really well but try to
| remove it )
|
|