Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #11   Report Post  
Old September 21st 03, 05:51 PM
Michael Black
 
Posts: n/a
Default

"Caveat Lector" ) writes:
Ah phonetics

The ARRL and many other national entities recommend the NATO phonetics
for Amateur Radio use as most Hams around the world recognize them.

The best one was printed in a magazine at some point. It was using
words that would always add to the confusion. I can't remember specific
examples, but it would have been like xylophone and psychiatrist.

Of course, it was intended to be funny (it was), and was not intended
to be used on the air (though I wouldn't put it past someone).

Michael VE2BVW

  #12   Report Post  
Old September 21st 03, 07:27 PM
LRod
 
Posts: n/a
Default

On Sun, 21 Sep 2003 08:15:24 -0700, "Caveat Lector"
wrote:

Ah phonetics


Sorry to tag on this post out of sequence.

The bottom line is communications. While it is true that by using a
*standard* alphabet one maximizes the probability of being understood,
in truth and in real practice, there are times when deviation may be
necessary.

First my qualifications: I was an air traffic controller for 30 years
and a pilot for some years before that, thus I have been intimately
familiar with the ICAO alphabet for nearly 40 years; using it on a
daily basis for most of that time. When everyone is on the same page
by official fiat, it is unusual to find the need for other than the
standard words.

However, in all the years I was DXing (on the way to Honor Roll), I
found that my particular callsign (N9AKE at the time) had a couple of
shortcomings in real world, difficult conditions. The "K" spoken as
"kilo" was often and easily lost in QSB or QRN. However, whenever I
used "kilowatt" there was a almost always complete understanding by
the other party, and I was able to successfully conclude my QSO.

The key here, however, is that "kilowatt" is almost universally
understood by hams, being a part of the argot of the pasttime. I doubt
I would have had more than a 50% success rate had I tried it at work.

Similarly, it is unlikely that substitutions others might try would
have as good a success rate unless they, too, were related to amateur
radio. If one were to try to use xenophobic, for example, most hams
(or other people) would choke on the word itself, since few are likely
to have even heard of it.

The argument made by someone that "kilowatt" could be confused for
"kilo" "watt" is specious, since in real communications, the use of
"kilowatt" is clearly a single word. If one were to use "kilo" and
"watt" as phonetics for discrete letters, they would be spoken clearly
and separately, whereas "kilowatt" is spoken almost as one syllable.

Context and common sense are somewhat of a determinant in successful
communications using phonetics. That is one reason why many DXers are
very successful using America, Brazil, Canada, Denmark, England,
France, Guatemala, etc., as phonetics. Hardly a DXer exists who
doesn't immediately recognize those words.

Finally we are not a commercial service, and public service aside, we
have no particular external requirement to get our communications
completed. There is no "officially sanctioned" alphabet that we are
required to use. Although, my skin crawls when I hear Bob say, "Broken
Old Bottle," the fact remains he is perfectly legal in doing so. In
amateur radio, success in communications is the only motive. If
"Boston London" (remember him?) gets it done regularly and reliably,
it's a good combination. If you don't want to have think one up, stick
with the ICAO (NATO) alphabet. For the vast majority of cases it's a
proven winner.


LRod

Master Woodbutcher and seasoned termite

Shamelessly whoring my website since 1999

http://www.woodbutcher.net
  #13   Report Post  
Old September 21st 03, 07:27 PM
LRod
 
Posts: n/a
Default

On Sun, 21 Sep 2003 08:15:24 -0700, "Caveat Lector"
wrote:

Ah phonetics


Sorry to tag on this post out of sequence.

The bottom line is communications. While it is true that by using a
*standard* alphabet one maximizes the probability of being understood,
in truth and in real practice, there are times when deviation may be
necessary.

First my qualifications: I was an air traffic controller for 30 years
and a pilot for some years before that, thus I have been intimately
familiar with the ICAO alphabet for nearly 40 years; using it on a
daily basis for most of that time. When everyone is on the same page
by official fiat, it is unusual to find the need for other than the
standard words.

However, in all the years I was DXing (on the way to Honor Roll), I
found that my particular callsign (N9AKE at the time) had a couple of
shortcomings in real world, difficult conditions. The "K" spoken as
"kilo" was often and easily lost in QSB or QRN. However, whenever I
used "kilowatt" there was a almost always complete understanding by
the other party, and I was able to successfully conclude my QSO.

The key here, however, is that "kilowatt" is almost universally
understood by hams, being a part of the argot of the pasttime. I doubt
I would have had more than a 50% success rate had I tried it at work.

Similarly, it is unlikely that substitutions others might try would
have as good a success rate unless they, too, were related to amateur
radio. If one were to try to use xenophobic, for example, most hams
(or other people) would choke on the word itself, since few are likely
to have even heard of it.

The argument made by someone that "kilowatt" could be confused for
"kilo" "watt" is specious, since in real communications, the use of
"kilowatt" is clearly a single word. If one were to use "kilo" and
"watt" as phonetics for discrete letters, they would be spoken clearly
and separately, whereas "kilowatt" is spoken almost as one syllable.

Context and common sense are somewhat of a determinant in successful
communications using phonetics. That is one reason why many DXers are
very successful using America, Brazil, Canada, Denmark, England,
France, Guatemala, etc., as phonetics. Hardly a DXer exists who
doesn't immediately recognize those words.

Finally we are not a commercial service, and public service aside, we
have no particular external requirement to get our communications
completed. There is no "officially sanctioned" alphabet that we are
required to use. Although, my skin crawls when I hear Bob say, "Broken
Old Bottle," the fact remains he is perfectly legal in doing so. In
amateur radio, success in communications is the only motive. If
"Boston London" (remember him?) gets it done regularly and reliably,
it's a good combination. If you don't want to have think one up, stick
with the ICAO (NATO) alphabet. For the vast majority of cases it's a
proven winner.


LRod

Master Woodbutcher and seasoned termite

Shamelessly whoring my website since 1999

http://www.woodbutcher.net
  #14   Report Post  
Old September 21st 03, 07:39 PM
Dee D. Flint
 
Posts: n/a
Default


"LRod" wrote in message
...
On Sun, 21 Sep 2003 08:15:24 -0700, "Caveat Lector"
wrote:

Ah phonetics


Sorry to tag on this post out of sequence.

The bottom line is communications. While it is true that by using a
*standard* alphabet one maximizes the probability of being understood,
in truth and in real practice, there are times when deviation may be
necessary.


I agree with that. There's been times when I've had to shift to some other
phonetic. But I always tried the standard first. Then if that failed, went
to one of the other frequently used phonetics such as "sugar" for "sierra".

First my qualifications: I was an air traffic controller for 30 years
and a pilot for some years before that, thus I have been intimately
familiar with the ICAO alphabet for nearly 40 years; using it on a
daily basis for most of that time. When everyone is on the same page
by official fiat, it is unusual to find the need for other than the
standard words.


That's the very reason for using the standard.

However, in all the years I was DXing (on the way to Honor Roll), I
found that my particular callsign (N9AKE at the time) had a couple of
shortcomings in real world, difficult conditions. The "K" spoken as
"kilo" was often and easily lost in QSB or QRN. However, whenever I
used "kilowatt" there was a almost always complete understanding by
the other party, and I was able to successfully conclude my QSO.


I have heard plenty of mixups on HF when kilowatt was used. Between talking
too fast and/or various foreign or dialectal accents and/or the fact that
there are plenty of older hams who may be somewhat hard of hearing, kilowatt
isn't a good choice as an alternate.

The key here, however, is that "kilowatt" is almost universally
understood by hams, being a part of the argot of the pasttime. I doubt
I would have had more than a 50% success rate had I tried it at work.

Similarly, it is unlikely that substitutions others might try would
have as good a success rate unless they, too, were related to amateur
radio. If one were to try to use xenophobic, for example, most hams
(or other people) would choke on the word itself, since few are likely
to have even heard of it.

The argument made by someone that "kilowatt" could be confused for
"kilo" "watt" is specious, since in real communications, the use of
"kilowatt" is clearly a single word. If one were to use "kilo" and
"watt" as phonetics for discrete letters, they would be spoken clearly
and separately, whereas "kilowatt" is spoken almost as one syllable.


See my comment above. Many people, for a variety of reasons, don't speak
clearly enough to make sure that there is a distinction.

Context and common sense are somewhat of a determinant in successful
communications using phonetics. That is one reason why many DXers are
very successful using America, Brazil, Canada, Denmark, England,
France, Guatemala, etc., as phonetics. Hardly a DXer exists who
doesn't immediately recognize those words.


Agreed. I'll use some of these if the standard isn't getting through but I
always try the standard first.

Finally we are not a commercial service, and public service aside, we
have no particular external requirement to get our communications
completed. There is no "officially sanctioned" alphabet that we are
required to use. Although, my skin crawls when I hear Bob say, "Broken
Old Bottle," the fact remains he is perfectly legal in doing so. In
amateur radio, success in communications is the only motive. If
"Boston London" (remember him?) gets it done regularly and reliably,
it's a good combination. If you don't want to have think one up, stick
with the ICAO (NATO) alphabet. For the vast majority of cases it's a
proven winner.



And that's why it should be used first and a switch made when necessary.

Dee D. Flint, N8UZE

  #15   Report Post  
Old September 21st 03, 07:39 PM
Dee D. Flint
 
Posts: n/a
Default


"LRod" wrote in message
...
On Sun, 21 Sep 2003 08:15:24 -0700, "Caveat Lector"
wrote:

Ah phonetics


Sorry to tag on this post out of sequence.

The bottom line is communications. While it is true that by using a
*standard* alphabet one maximizes the probability of being understood,
in truth and in real practice, there are times when deviation may be
necessary.


I agree with that. There's been times when I've had to shift to some other
phonetic. But I always tried the standard first. Then if that failed, went
to one of the other frequently used phonetics such as "sugar" for "sierra".

First my qualifications: I was an air traffic controller for 30 years
and a pilot for some years before that, thus I have been intimately
familiar with the ICAO alphabet for nearly 40 years; using it on a
daily basis for most of that time. When everyone is on the same page
by official fiat, it is unusual to find the need for other than the
standard words.


That's the very reason for using the standard.

However, in all the years I was DXing (on the way to Honor Roll), I
found that my particular callsign (N9AKE at the time) had a couple of
shortcomings in real world, difficult conditions. The "K" spoken as
"kilo" was often and easily lost in QSB or QRN. However, whenever I
used "kilowatt" there was a almost always complete understanding by
the other party, and I was able to successfully conclude my QSO.


I have heard plenty of mixups on HF when kilowatt was used. Between talking
too fast and/or various foreign or dialectal accents and/or the fact that
there are plenty of older hams who may be somewhat hard of hearing, kilowatt
isn't a good choice as an alternate.

The key here, however, is that "kilowatt" is almost universally
understood by hams, being a part of the argot of the pasttime. I doubt
I would have had more than a 50% success rate had I tried it at work.

Similarly, it is unlikely that substitutions others might try would
have as good a success rate unless they, too, were related to amateur
radio. If one were to try to use xenophobic, for example, most hams
(or other people) would choke on the word itself, since few are likely
to have even heard of it.

The argument made by someone that "kilowatt" could be confused for
"kilo" "watt" is specious, since in real communications, the use of
"kilowatt" is clearly a single word. If one were to use "kilo" and
"watt" as phonetics for discrete letters, they would be spoken clearly
and separately, whereas "kilowatt" is spoken almost as one syllable.


See my comment above. Many people, for a variety of reasons, don't speak
clearly enough to make sure that there is a distinction.

Context and common sense are somewhat of a determinant in successful
communications using phonetics. That is one reason why many DXers are
very successful using America, Brazil, Canada, Denmark, England,
France, Guatemala, etc., as phonetics. Hardly a DXer exists who
doesn't immediately recognize those words.


Agreed. I'll use some of these if the standard isn't getting through but I
always try the standard first.

Finally we are not a commercial service, and public service aside, we
have no particular external requirement to get our communications
completed. There is no "officially sanctioned" alphabet that we are
required to use. Although, my skin crawls when I hear Bob say, "Broken
Old Bottle," the fact remains he is perfectly legal in doing so. In
amateur radio, success in communications is the only motive. If
"Boston London" (remember him?) gets it done regularly and reliably,
it's a good combination. If you don't want to have think one up, stick
with the ICAO (NATO) alphabet. For the vast majority of cases it's a
proven winner.



And that's why it should be used first and a switch made when necessary.

Dee D. Flint, N8UZE



  #16   Report Post  
Old September 21st 03, 09:40 PM
Ham Dat Am
 
Posts: n/a
Default

"Roger Wussman" wrote in message
...

Bottom line -- use the NATO phonetics -- so most all will understand and
always during an emergency.
--
73 From The Signal In The Noise
Caveat Lector Ya All


Bottom line? Foxtrot Uniform.


Forever Uninformed (:-)
Or
Forget Uniformity (:-(

HDA


  #17   Report Post  
Old September 21st 03, 09:40 PM
Ham Dat Am
 
Posts: n/a
Default

"Roger Wussman" wrote in message
...

Bottom line -- use the NATO phonetics -- so most all will understand and
always during an emergency.
--
73 From The Signal In The Noise
Caveat Lector Ya All


Bottom line? Foxtrot Uniform.


Forever Uninformed (:-)
Or
Forget Uniformity (:-(

HDA


  #18   Report Post  
Old October 13th 03, 07:55 AM
Steve Silverwood
 
Posts: n/a
Default

In article , jder8745
@aol.com says...
Recently I hear more and more hams using "kilowatt" as the phonetic for the
letter K. The correct phonetic is "kilo".


Could this be considered, "hamming it up?"

groan

--

-- //Steve//

Steve Silverwood, KB6OJS
Fountain Valley, CA
Email:
Web:
http://home.earthlink.net/~kb6ojs_steve
  #19   Report Post  
Old October 13th 03, 07:55 AM
Steve Silverwood
 
Posts: n/a
Default

In article , jder8745
@aol.com says...
Recently I hear more and more hams using "kilowatt" as the phonetic for the
letter K. The correct phonetic is "kilo".


Could this be considered, "hamming it up?"

groan

--

-- //Steve//

Steve Silverwood, KB6OJS
Fountain Valley, CA
Email:
Web:
http://home.earthlink.net/~kb6ojs_steve
  #20   Report Post  
Old October 14th 03, 01:13 AM
Dave Bushong
 
Posts: n/a
Default

JDer8745 wrote:

Howdy,

Recently I hear more and more hams using "kilowatt" as the phonetic for the
letter K. The correct phonetic is "kilo".

73 de Jack, K9CUN. That's...

kickapoo niner certain underwear neurosis



Of course, for my callsign I could use

Knife Zucchini One Oedipus

or even

Kilo Zero One One

73,
kz1o

Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Wrong S-meter in Hallicrafters SX-28? Phil Nelson Boatanchors 44 December 11th 04 02:05 AM
Wrong S-meter in Hallicrafters SX-28? Phil Nelson Boatanchors 0 December 7th 04 10:44 PM
WRONG PHONETICS Caveat Lector Dx 1 September 21st 03 04:22 PM
FS: Ten Tec Omni D - sorry wrong email addr. before! GS Boatanchors 0 July 16th 03 07:24 PM
GAY BISHOPS: WHAT'S WRONG WITH THAT? Don Souter General 0 July 3rd 03 11:51 PM


All times are GMT +1. The time now is 03:37 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 RadioBanter.
The comments are property of their posters.
 

About Us

"It's about Radio"

 

Copyright © 2017