Micronta 21-525B. Reading the instructions from the web and it says "Push
transmit button and rotate the calibration control until the meters needle
aligns with the Cal mark"

The problem is the CAL mark is 1" wide , sorta like this, on the right side
of the meter.

|_______|
cal

Do you adjust to the beginning of the area, middle or far right where the
CAL is printed? The entire CAL area is in red.


Thanks!




--

Jim Douglas
http:\\www.genesis-software.com

Latitude 32.5818
Longitude -96.5412
Elevation 497

Jim Douglas wrote:

Micronta 21-525B. Reading the instructions from the web and it says "Push
transmit button and rotate the calibration control until the meters needle
aligns with the Cal mark"

The problem is the CAL mark is 1" wide , sorta like this, on the right side
of the meter.

|_______|
cal

Do you adjust to the beginning of the area, middle or far right where the
CAL is printed? The entire CAL area is in red.

My guess is all the way to the CAL mark... I seem to remember having one of
those.

dxAce

dxAce wrote:

Jim Douglas wrote:

Micronta 21-525B. Reading the instructions from the web and it says "Push
transmit button and rotate the calibration control until the meters needle
aligns with the Cal mark"

The problem is the CAL mark is 1" wide , sorta like this, on the right side
of the meter.

|_______|
cal

Do you adjust to the beginning of the area, middle or far right where the
CAL is printed? The entire CAL area is in red.

My guess is all the way to the CAL mark... I seem to remember having one of
those.

My MFJ VHF SWR meter is pretty much the same, all the way to the right by the CAL
mark.



dxAce

Thanks for the quick response. I was afraid of that answer and the rest of
the calibration is way off if I set it to the far right! Back to work I go!
Thanks again!


"dxAce" wrote in message
...


Jim Douglas wrote:

Micronta 21-525B. Reading the instructions from the web and it says
"Push
transmit button and rotate the calibration control until the meters
needle
aligns with the Cal mark"

The problem is the CAL mark is 1" wide , sorta like this, on the right
side
of the meter.

|_______|
cal

Do you adjust to the beginning of the area, middle or far right where
the
CAL is printed? The entire CAL area is in red.

My guess is all the way to the CAL mark... I seem to remember having one
of
those.

dxAce

Jim Douglas wrote:

Thanks for the quick response. I was afraid of that answer and the rest of
the calibration is way off if I set it to the far right! Back to work I go!
Thanks again!

What is off on it?



"dxAce" wrote in message
...


Jim Douglas wrote:

Micronta 21-525B. Reading the instructions from the web and it says
"Push
transmit button and rotate the calibration control until the meters
needle
aligns with the Cal mark"

The problem is the CAL mark is 1" wide , sorta like this, on the right
side
of the meter.

|_______|
cal

Do you adjust to the beginning of the area, middle or far right where
the
CAL is printed? The entire CAL area is in red.

My guess is all the way to the CAL mark... I seem to remember having one
of
those.

dxAce

The tic mark next to SET or CAL is the alignment point. The red band
indicates an excessively high SWR when in measurement mode (after
calibration). I have a Micronta 21-520A and would not consider it to be very
accurate.

Tom

"Jim Douglas" wrote in message
news:9XOXc.326303$%_6.256483@attbi_s01...
Thanks for the quick response. I was afraid of that answer and the rest of
the calibration is way off if I set it to the far right! Back to work I
go!
Thanks again!


"dxAce" wrote in message
...


Jim Douglas wrote:

Micronta 21-525B. Reading the instructions from the web and it says
"Push
transmit button and rotate the calibration control until the meters
needle
aligns with the Cal mark"

The problem is the CAL mark is 1" wide , sorta like this, on the right
side
of the meter.

|_______|
cal

Do you adjust to the beginning of the area, middle or far right where
the
CAL is printed? The entire CAL area is in red.

My guess is all the way to the CAL mark... I seem to remember having one
of
those.

dxAce